Dukane iQ Series User Manual Page 91
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 10 - Options
Page 83
Dukane Manual Part Number 403-572-03
Continued from Previous Page
iQ LinQTM Ethernet/IPTM Module
Part Number - 110- 4644
The EtherNet/IP option module allows the iQ generator
to connect to an EtherNet/IP network. The option
module is an external DIN-rail mounted device that acts
as a bridge between the automation network and an iQ
generator’s RS-232 port. See Figure 10-17 below.
Control Parameters available via EtherNet/IP
1. Set weld method to Time, Energy, or Peak Power. Set
associated value in seconds, joules, or watts.
2. Set Amplitude, Ramp Up Time, and Ramp Down
Time.
3. Enable and set Trigger by Power parameters.
4. Enable and set Hold time.
5. Enable and set Afterburst delay and duration.
6. Enable checking for Suspect Parts. Set maximum and
minimum values for Time, Power and/or Energy.
7. Enable checking for Bad Parts. Set maximum and
minimum values for Time, Power and/or Energy.
8. Configure advanced hardware settings including
Phase, Free Run Frequency, Frequency Lock and
Hold, and Frequency limits.
Parameters that can be obtained via Ethernet/IP
1. All parameters that can be congured via EtherNet/
IP.
2. Real time data which includes welder state (ultra-
sound active or not), frequency, power, and ampli-
tude.
3. Weld cycle data from previous weld which includes:
• Cycle Count
• Good, Bad, and Suspect Part information
• Process Limit setting exceeded or not reached if Bad
or Suspect Part checking is enabled
• Weld Time
• Weld Energy
• Peak Power
For information on how to control and/or monitor specic
parameters, iQ Generator EtherNet/IP Communication and
Control documentation is available.
Signing a non-disclosure agreement is required to obtain this
documentation.
Figure 10-17 EtherNet/IPTM Module
EtherNet/IP
iQLinQ
+24V
CONFIG
4.65
[118]
1.77
[45]
5.41
[137.5]
in
mm
Front View
Top View
Status LEDs
Connect to iQ Generator’s
J4 Port
Connect to EtherNet/
IP Network
- User’s Manual 1
- Revision History 3
- Contents 5
- Continued 6
- SECTION 1 9
- Page left intentionally blank 10
- General User Information 11
- Generator Overview 12
- Key Generator Features 12
- SECTION 2 13
- General Considerations 15
- Plastics Health Notice 16
- Electrical Safety 16
- Domestic Power Grounding 17
- International Power Grounding 17
- Lifting the Equipment 18
- SECTION 3 19
- Before Installation 21
- Lockout/Tagout 22
- Unpacking 23
- Horizontal Bench Chassis 24
- RFI Grounding 25
- Connecting Cables 26
- Power Cords 27
- SECTION 4 29
- Panel Layout Overview 31
- LINE VOLTAGE: 32
- 200-240 Vac 32
- 50/60Hz, 15A 32
- AC Power Inlet Panel 33
- System I/O Panel 34
- 1 2 3 4 5 35
- 11 12 13 14 15 35
- System Outputs Connector 37
- (+22V Power Supply) 38
- (+22V Power Ground) 38
- (Any Fault Status Output) 39
- (Suspect Part Status Output) 41
- (Isolated Common) 41
- (Not Used) 41
- Ultrasound Output Connector 41
- Conguration Port Connector 41
- SECTION 5 43
- Control Panel and Display 45
- Overview 45
- Display Controls 46
- LCD Display 47
- Power Output Level Scale 47
- System Operating Mode Keys 47
- INFO Key 48
- Status LEDs 49
- System Parameter Settings 50
- Section 6 51
- Programming Examples 54
- SECTION 7 57
- System Verication Tests 59
- System Test 60
- Probe Operation 61
- Stop Ultrasound Output 62
- SECTION 8 63
- No Ultrasonic Output 65
- INFO Status LED: RED 66
- Welding Problems 67
- SECTION 9 69
- Display/Control Panel 71
- Air Ventilation Slots 72
- I/O Connector 72
- AC Power Cord 72
- SECTION 10 73
- Power Inlet Options 75
- 120 volt line cord 76
- I/O Panel Options 77
- Option Panel Modules 78
- MPC Probe Control 79
- (6 PLCS) 80
- Rear Connections 81
- Front Connections 81
- E in Figure 10 - 9) 82
- MPC Interface Status LEDs 82
- MPC Cycle Flow Chart 83
- Part Number - 110- 4183 84
- Part Number - 110- 4397 85
- NPN TO PNP CONVERSION 86
- PNP TO NPN CONVERSION 87
- +5V TO +24V PNP CONVERSION 88
- 110-4397 88
- RS-232 Interface Option 89
- Part Number - 110-4554 90
- EtherNet/IP 91
- SECTION 11 93
- OPTIONAL 95
- FRONT RACK MOUNTING 95
- .220 DIA. SLOTS 96
- [5.59] (4 PLCS) 96
- Operating Environment 97
- Weight: 97
- AC Power Requirements 98
- System Process Controls 99
- Regulatory Agency Compliance 100
- SECTION 12 101
- Contacting Dukane 103
- APPENDICES 105
- List of Figures 107
- List of Figures continued 108
- List of Tables 109
- Page 103 111
- Continued 112
- Dukane ISO 115
- Part No. 403 116
Related products and manuals for Power supply units Dukane iQ Series
(144 pages)© 2020, manymanuals.com. All rights reserved. | 2.884 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals