Dukane iQ Series User Manual Page 77
- Page / 116
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 10 - Options
Page 69
Dukane Manual Part Number 403-572-03
I/O Panel Options
Single I/O Connector
See B in Figure 10 - 4 where the I/O panel is set up for the
single I/O connector, a HD15F type. The generator label
for this connector is, SYSTEM INPUTS/OUTPUTS.
Another label identies the connector as J12.
The I/O panel can be customized with multiple types of
connectors such as the single HD15F, terminal blocks, etc.
Contact your local sales representative for more details.
Table 10-I shows an example of a customized option:
Pins/Signals duplicate a Dukane DPC-I generator.
Pin Signal Name Signal Description
1 + 22VDC Current limited to 250 mA maximum
2 Ground 22VDC Return (chassis ground)
3 Ground Status Outputs/Driver/Monitor Return
4 Status Driver STATUS Driver Output (1 Amp max.)
5 Ultrasound Active Status Ultrasound Statup Output (Active Low)
6 Overload Fault Status Overload Fault Output (Active Low)
7 Isolated Common Isolated Operate Input Common (7 & 8) JU726
8 Operate Input Sw Closure Operate Input (2 & 8)JU724/725
9 Overtemperature Fault Overtemperature Fault Output (Active Low)
10 System Fault System Fault Output (Active Low)
11 Not Used Reserved - HPPI Signal
12 Amplitude Setting Amplitude Setting Monitor (10.0V = 100%)
13 Power Signal Common Power Signal Common
14 Power Signal* Power Signal Monitor Output* (1mV = 1 Watt)
15 Loop Fault Current Loop Fault Output (Active Low)
Table 10- I HD15F Example of Customized System Inputs/Outputs Connector Signals
5 4 3 2 1
5 4 3 2 1
15 14 13 12 11
15 14 13 12 11
6
6
10
10
Figure 10 - 3 HD-15F for System Inputs/Outputs
Connector
Figure 10- 4 Option Panel and I/O Panel
(NOTE: Shown are the Option panel with Remote
Amplitude Control Module, and the I/O panel with a
single I/O connector.)
Option Panel
I/O Panel
A
B
* Power Signal Output Monitor (Pin 14) is available only if the generator is equipped
with the optional Power Signal Board.
- User’s Manual 1
- Revision History 3
- Contents 5
- Continued 6
- SECTION 1 9
- Page left intentionally blank 10
- General User Information 11
- Generator Overview 12
- Key Generator Features 12
- SECTION 2 13
- General Considerations 15
- Plastics Health Notice 16
- Electrical Safety 16
- Domestic Power Grounding 17
- International Power Grounding 17
- Lifting the Equipment 18
- SECTION 3 19
- Before Installation 21
- Lockout/Tagout 22
- Unpacking 23
- Horizontal Bench Chassis 24
- RFI Grounding 25
- Connecting Cables 26
- Power Cords 27
- SECTION 4 29
- Panel Layout Overview 31
- LINE VOLTAGE: 32
- 200-240 Vac 32
- 50/60Hz, 15A 32
- AC Power Inlet Panel 33
- System I/O Panel 34
- 1 2 3 4 5 35
- 11 12 13 14 15 35
- System Outputs Connector 37
- (+22V Power Supply) 38
- (+22V Power Ground) 38
- (Any Fault Status Output) 39
- (Suspect Part Status Output) 41
- (Isolated Common) 41
- (Not Used) 41
- Ultrasound Output Connector 41
- Conguration Port Connector 41
- SECTION 5 43
- Control Panel and Display 45
- Overview 45
- Display Controls 46
- LCD Display 47
- Power Output Level Scale 47
- System Operating Mode Keys 47
- INFO Key 48
- Status LEDs 49
- System Parameter Settings 50
- Section 6 51
- Programming Examples 54
- SECTION 7 57
- System Verication Tests 59
- System Test 60
- Probe Operation 61
- Stop Ultrasound Output 62
- SECTION 8 63
- No Ultrasonic Output 65
- INFO Status LED: RED 66
- Welding Problems 67
- SECTION 9 69
- Display/Control Panel 71
- Air Ventilation Slots 72
- I/O Connector 72
- AC Power Cord 72
- SECTION 10 73
- Power Inlet Options 75
- 120 volt line cord 76
- I/O Panel Options 77
- Option Panel Modules 78
- MPC Probe Control 79
- (6 PLCS) 80
- Rear Connections 81
- Front Connections 81
- E in Figure 10 - 9) 82
- MPC Interface Status LEDs 82
- MPC Cycle Flow Chart 83
- Part Number - 110- 4183 84
- Part Number - 110- 4397 85
- NPN TO PNP CONVERSION 86
- PNP TO NPN CONVERSION 87
- +5V TO +24V PNP CONVERSION 88
- 110-4397 88
- RS-232 Interface Option 89
- Part Number - 110-4554 90
- EtherNet/IP 91
- SECTION 11 93
- OPTIONAL 95
- FRONT RACK MOUNTING 95
- .220 DIA. SLOTS 96
- [5.59] (4 PLCS) 96
- Operating Environment 97
- Weight: 97
- AC Power Requirements 98
- System Process Controls 99
- Regulatory Agency Compliance 100
- SECTION 12 101
- Contacting Dukane 103
- APPENDICES 105
- List of Figures 107
- List of Figures continued 108
- List of Tables 109
- Page 103 111
- Continued 112
- Dukane ISO 115
- Part No. 403 116
Related products and manuals for Power supply units Dukane iQ Series
(144 pages)© 2020, manymanuals.com. All rights reserved. | 0.735 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals