Dukane iQ Series User Manual Page 111
- Page / 144
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 105
Section 11 - Options
Dukane Manual Part No. 403-588-00
5mA0mA
20%
0%
40%
60%
80%
100%
10mA 15mA 20mA
4mA
Current
Loop
Fault
Region
36%
Figure 11-9 Current Loop Transfer Function Graph
Figure 11-10 Generator Rear View - Optional Remote Amplitude Control Module
LINE VOLTAGE:
200-240 Vac
50/60Hz, 10A
PE
J1
J4
J3
J2
J7
SYSTEM INPUTS
SYSTEM OUTPUTS
CONFIGURATION
U/S
CURRENT LOOP
INPUT
STATUS
POS
NEG
SHIELD
E-STOP
Current Loop Fault Indicator - Green/Red LED
Current Loop Connector
J9
ETHERNET
Remote Amplitude Control
Module and EtherNet/IP
Part Number - 110- 4183 or
110-4589 for 3600W and 4800W
High Power Units
This optional module combines the EtherNet/IP and
Remote Amplitude Control interfaces. See Pages 31-32
for information on the EtherNet/IP connector.
This module enables remote control of output amplitude of
the iQ system. The control interface is a 4–20mA current
loop. The current loop connector and fault indicator are
shown below in Figure 11–10. The output can be adjusted
from 36% to 100%. The scale factor is a 4% amplitude
change for each mA change. A graph of amplitude output
as a function of loop current is shown in Figure 11-9. The
current loop compliance voltage is 6 volts minimum.
Failure to provide at least 4mA of loop current is sensed as a
fault and will produce minimum amplitude output.
The current loop fault indicator is a bi–color LED. It is green
when the current is between 4 and 20mA and red when the
current is below 2mA.
Current Loop Fault
If a current loop source is not available, an external +24VDC
power supply can be connected to the POS and NEG terminals
of J7. (See Figure 11-11.) A +22VDC supply is also available
on System Output Pins 1(+) and 3(-).
Continued
- User’s Manual 1
- Revision History 3
- Contents 5
- SECTION 1 7
- General User Information 9
- Generator Overview 10
- Key Generator Features 10
- SECTION 2 11
- Page 6 12
- General Considerations 13
- Plastics Health Notice 14
- Electrical Safety 14
- Domestic Power Grounding 15
- International Power Grounding 15
- Lifting the Equipment 16
- SECTION 3 17
- Page 12 18
- Before Installation 19
- Page 14 20
- Unpacking 21
- Placement 21
- RFI Grounding 22
- Connecting Cables 23
- Automation Controlled Probe 24
- SECTION 4 25
- Page 20 26
- Rear Panel Layout Overview 27
- AC Power Inlet Panel 28
- System I/O Panel 28
- 1 2 3 4 5 30
- 11 12 13 14 15 30
- Page 26 32
- , on the front of the MPC 33
- (System Ready Status Output) 34
- (Suspect Part Status Output) 34
- (Isolated Common) 34
- (Not Used) 34
- Ultrasound Output Connector 36
- Conguration Port Connector 37
- EtherNet/IP Port Connector 37
- SECTION 5 39
- Page 34 40
- Front Panel Controls 41
- System Operating Mode Keys 42
- Navigation Keys (4) 43
- Soft Keys Bordering the 43
- Display (3) 43
- Hot Keys (8) 44
- Lighted Power Indicator 45
- Screen Basics 46
- OPERATE 47
- Page 42 48
- SECTION 6 49
- Page 44 50
- Start-up Sequence 52
- Stopping the Weld Cycle 53
- Using the Menus 54
- ONLINE 55
- Page 50 56
- Power Enabled 56
- Remote Amplitude Board 57
- PRE-WELD 58
- MPC Module Installed 60
- POST-WELD 62
- Afterburst 63
- Bad Limits 64
- Suspect Limits 64
- Section 6 – Operation 65
- Part Limits 65
- Setup Control 66
- Name Setup 66
- > is moved to NAME SETUP 66
- Copying a Setup 67
- Erase Setup 68
- ONLINE 69
- AUTO 01 69
- IN CYCLE 71
- Using the INFO Menus 72
- Network Settings 79
- Moving to the Next Sub-menu 79
- Page 76 82
- SECTION 7 83
- Page 78 84
- Page 80 86
- SECTION 8 87
- System Operational Testing 87
- Page 82 88
- System Verication Tests 89
- System Test 90
- Probe Operation 91
- Page 86 92
- SECTION 9 93
- Troubleshooting 93
- Page 88 94
- 11 12 13 14 15 95
- Welding Problems 96
- SECTION 10 97
- Maintenance 97
- Page 92 98
- Front and Rear Panels 99
- Page 94 100
- SECTION 11 101
- Page 96 102
- Power Inlet Options 103
- I/O Panel Options 104
- Interface and EtherNet/IP 105
- Multi- Probe Control (MPC) 105
- MPC Probe Control 106
- Cut Outs 107
- Continued from Previous Page 107
- Continued 107
- MPC Cycle Illustration 110
- MPC Cycle Flow Chart 110
- Remote Amplitude Control 111
- Module and EtherNet/IP 111
- Remote Amplitude 112
- Automation Thruster Control 113
- RS-232 Interface Option 115
- Part Number - 110 - 4554 116
- SECTION 12 117
- Contacting Dukane 117
- Page 112 118
- Page 114 120
- SECTION 13 121
- Specications 121
- Page 116 122
- Page 117 123
- Section 13 - Specications 123
- Operating Environment 124
- Weights 124
- AC Power Requirements 125
- Ultrasonic Pressure 126
- Page 121 127
- Regulatory Agency Compliance 128
- System Parameter Settings 129
- Overview 129
- APPENDICES 131
- Page 126 132
- Appendix A 133
- List of Figures 133
- List of Tables 136
- Appendix B 136
- Page 131 137
- Page 132 138
- S Continued 142
- Dukane ISO 143
- Part No. 403-588-00 144
Related products and manuals for Power supply units Dukane iQ Series
(2 pages)© 2020, manymanuals.com. All rights reserved. | 1.457 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals